Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateTrusted Garage Door Repair for Manchester Homeowners
When a garage door quits, it usually picks the worst moment: the morning you’re running late, or the evening before a storm rolls in off the Merrimack. Radiant Garage Door Repair focuses on one trade and nothing else, so the technician who arrives knows your door and your opener instead of guessing at them. Our technicians have up to 10 years of experience, and we service eight of the most widely installed brands in residential America, including LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. Most repair calls in Manchester can be handled the same day. We answer 24/7 and run fast dispatch from 7am to 7pm, Sunday through Friday.
Call (888) 459-1302 and we’ll get a technician headed your way. Estimates are free, and the price is quoted and agreed before any work starts.
Garage Door Spring Repair
Garage Door Spring Repair is the fix for the torsion or extension springs that carry most of your door’s weight, and it’s the single most common repair we handle in Manchester. When a spring snaps you’ll hear a sharp bang, and the door becomes too heavy to lift by hand or refuses to open at all. Springs fatigue from years of daily cycles and from the temperature swings here, where a January cold snap can finish off a spring that was already near the end. We replace the spring, balance the door, and check the cables and drums while we’re there. Typical spring repair in Manchester runs $180 – $340 for one spring; a matched pair is usually replaced together and costs about twice that. The written estimate sets the final price.
Worn Torsion Springs
Torsion springs sit on a shaft above the door and do the heavy lifting every time you open it. A door that feels suddenly heavy, or a spring with a visible gap in the coil, means it’s ready to be replaced. We match the spring to your door’s weight so it lasts as long as it should.
Extension Spring Replacement
Extension springs run along the tracks on either side and stretch as the door closes. They’re common on older Manchester doors, and they wear out quietly until one lets go. We replace them in pairs and check the safety cables that keep a broken spring from flying loose.
Springs are under heavy tension and are genuinely dangerous to touch. Please don’t try to wind, cut or remove one yourself. This is work for a trained technician.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Garage Door Sensor Repair
Garage Door Sensor Repair fixes the safety eyes near the floor that tell your opener the doorway is clear. When they’re misaligned, dirty, or a wire has been nicked, the door reverses partway down, closes and reopens, or won’t budge from the open position. It’s one of the most frequent calls we get, and it’s often a quick fix once we’ve traced the actual cause with a meter rather than a guess. We realign the sensors, test the beam, and repair or replace the wiring and brackets as needed. Sensor repairs usually fall within our general garage door repair range of $150 – $600, and the written estimate sets the final price.
Misaligned Safety Eyes
A bumped bracket or a shifted track can knock the beam out of line, and the opener shuts down to be safe. We line the sensors up and confirm the door reverses correctly on contact. It’s a small adjustment that solves a big headache.
Faulty Sensor Wiring
Rodents, moisture, and simple wear can damage the low-voltage wire that runs to each sensor. We test the circuit, repair or replace the run, and make sure both eyes talk to the opener. You’ll know it’s fixed when the door closes smoothly without reversing.
Emergency Garage Door Repair
Emergency Garage Door Repair is for the situations that can’t wait: a door stuck half-open, a snapped cable whipping loose, or a door that’s come off its track and is hanging at an angle. A door left open leaves your home exposed, and one jammed in the opening traps your car inside. We prioritize these calls in Manchester and get a technician out as fast as we can. We answer 24/7, and a call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Emergency repairs fall within our general repair range of $150 – $600, and the written estimate sets the final price before any work begins.
Doors Off Their Tracks
A door that’s jumped the track is unstable and shouldn’t be forced up or down by hand. We assess the rollers, hinges, and track, then bring the door back into alignment. Forcing it can bend panels and turn a smaller repair into a bigger one.
Broken Cables and Snapped Springs
A snapped cable or spring leaves the door unsupported and genuinely unsafe to operate. We secure the door first, then make the repair. Please keep everyone clear of a door in this condition until a technician arrives.
Garage Door Panel Replacement
Garage Door Panel Replacement swaps out a damaged section of your door instead of the whole thing, which is often the smarter and less expensive path. It’s the right call when a panel is dented, cracked, bowed, or rusted through, or after a car has backed into the door. We match panel profiles, colors, and window inserts from Clopay, Amarr, Wayne Dalton, and Raynor so the repaired door looks whole again. If only one or two sections are damaged, we’ll tell you honestly whether replacement makes sense over a new door. Panel replacement in Manchester typically runs $250 – $500, with the written estimate setting the final price. A free measure and written quote come first.
Dented and Damaged Sections
Impact damage is the usual reason a panel needs replacing, whether from a vehicle, a stray ball, or a storm-blown branch. A dented panel can also throw off the door’s balance and strain the opener. We replace the affected section and check that the door still runs true.
Matching Panels to Your Door
Getting a panel that matches isn’t just about color, it’s about the profile, thickness, and window style. We work from your door’s make and model to find the right fit. When an exact match isn’t available, we’ll walk you through the closest options before you commit.
Garage Door Maintenance
Garage Door Maintenance is the tune-up that keeps a working door working, and it’s the cheapest way to avoid a breakdown later. We recommend it once a year, and it’s worth doing before winter sets in and the cold puts extra stress on springs and moving parts. A maintenance visit includes lubricating the springs, hinges, and rollers, checking the balance and travel limits, testing the safety reverse, and tightening the hardware. It catches worn parts before they fail. Maintenance pricing varies with the door, so we quote it per job with a free estimate, and the written price is agreed before we start.
Annual Tune-Ups
Once a year is enough for most homes, and it keeps the opener, springs, and track in step with each other. A door that’s been squeaking or moving sluggishly usually just needs attention. We’ll flag anything that’s wearing out so you can plan for it.
What a Maintenance Visit Covers
We clean and lubricate the moving parts, check the balance and spring tension, and test the safety reverse and sensors. We also look at the rollers, cables, and hinges for early signs of wear. You’ll get a plain rundown of what’s fine and what needs watching.
Garage Door Roller Replacement
Garage Door Roller Replacement is the fix for a door that shudders, screeches, or grinds as it moves up and down the track. Rollers wear flat or seize over time, and a bad roller drags on the whole system and strains the opener. It’s an easy repair to put off and a bad one to ignore. We replace rollers in complete sets so the door runs evenly, and we check the track and hinges at the same time. Roller replacement in Manchester typically runs $110 – $220, and the written estimate sets the final price. The improvement is usually obvious the first time you open the door.
Noisy or Sticking Rollers
A door that squeals or jerks along the track is telling you its rollers are worn. Seized rollers can also pull the door off balance and wear the tracks. Replacing them restores a smooth, quiet ride.
Nylon Versus Steel Rollers
Steel rollers are durable but noisy, while nylon rollers run quieter and are easier on the track. We’ll match the roller type to your door and how much it’s used. Either way, we install quality parts that hold up.
Commercial Garage Door Repair
Commercial Garage Door Repair covers the heavier doors and high-cycle openers that keep a Manchester business running, from roll-up doors to overhead sectional doors. When a commercial door won’t open, it stops deliveries, blocks customers, or shuts a bay down entirely. We service commercial doors and their operators with the same brand knowledge we bring to homes, including LiftMaster and Chamberlain openers that are common on commercial setups. Because commercial doors run far more cycles than residential ones, worn parts show up sooner. Commercial repairs are quoted per job after we assess the door, and the written estimate sets the final price.
High-Cycle Doors and Operators
Commercial doors cycle dozens of times a day, so springs, rollers, and openers wear faster than at home. We inspect the whole system, not just the part that failed. That way the next weak link doesn’t strand you a week later.
Keeping a Business Door Moving
A door that’s down costs money every hour, so we move quickly to diagnose and repair. We’ll tell you straight whether a fix or a replacement makes more sense. Getting you operating again is the priority.
Garage Door Cable Repair
Garage Door Cable Repair deals with the steel cables that work with your springs to lift and lower the door, and a damaged cable needs attention fast. A cable that’s frayed, kinked, or snapped leaves the door unstable and can send it crashing down on one side. You might notice a slack cable, a door hanging crooked, or a loud snap. Cables and springs work as a system, so we inspect both together and replace what’s worn. Cable repair in Manchester typically runs $130 – $250, and the written estimate sets the final price before any work begins. A snapped cable should never be operated or pried at.
Frayed and Stretched Cables
Cables fray with age and use, and a frayed cable is a cable about to fail. Stretched cables also throw the door off balance and put uneven load on the springs. We replace them and rebalance the door so it lifts smoothly.
Why Cables Need a Pro
Cables hold serious tension and are tied to the spring system, which makes them one of the most dangerous parts to handle. Please don’t attempt to loosen or replace one yourself. A trained technician has the tools and the know-how to do it safely.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We service LiftMaster and Chamberlain openers and know where their gears, logic boards, and safety eyes tend to wear out. Genie and Craftsman openers are just as familiar to us, and we handle both legacy units and modern smart-home-integrated systems. On the door side, we repair and install Clopay and Amarr products across the value and premium segments.
We also work on Wayne Dalton and Raynor doors, matching panels and hardware so your door looks and runs right. Because we focus only on garage doors and openers, every tool and technique we use is built for this trade. Whether you have LiftMaster, Clopay, or any other make, we can help.
Signs You Need a Pro Right Now
- A loud bang from the garage. That’s often a spring breaking, and the door becomes too heavy and unsafe to lift. Stay clear and call us rather than trying to open it.
- The door reverses or won’t close. This usually points to misaligned or faulty safety sensors. It’s rarely safe to override them, so let a technician trace the cause.
- The door hangs crooked or comes off its track. An off-track door is unstable and can fall or bend panels if forced. It needs a professional to bring it back into alignment.
- Grinding, squealing, or shuddering. Worn rollers or dry, tired hardware are usually behind it. Left alone, the strain spreads to the opener and tracks.
- The opener runs but the door doesn’t move. A broken spring, snapped cable, or decoupled trolley could all be the cause. We diagnose which one before touching anything.
Our Process, Step by Step
- 1
We take your call and ask the right questions. Tell us the brand and what the door is doing, and we’ll get a clear picture before we arrive. That head start means fewer surprises and a faster fix.
- 2
We diagnose the actual problem. A technician inspects the door, opener, springs, cables, and sensors, using a meter and a trained eye rather than a guess. We work on your specific brand and model, not a generic approximation of it.
- 3
We explain what’s wrong and give you a written estimate. You’ll hear the diagnosis in plain language and see the price before any work starts. Repair or replace, we’ll tell you which one actually makes sense.
- 4
We make the repair. Once you approve the estimate, we do the work with parts matched to your door and opener. The goal is a fix that holds, not a patch that fails next month.
- 5
We test and confirm the door is back to working the way it should. We run the door through full cycles, check the safety reverse, and make sure everything is balanced. You see it working before we leave.
How Much Does Garage Door Repair Cost in Manchester?
Garage door repair in Manchester typically costs between $150 and $600 for most jobs, depending on the part and how involved the fix is. A typical spring repair in Manchester runs $180 – $340 for one spring, and cable repair runs $130 – $250. Roller replacement runs $110 – $220, and a damaged panel runs $250 – $500. Opener repair is $120 – $320, while a full new door installation is $700 – $2200 and a new opener installs for $250 – $550.
What affects the price is mostly the part, the door’s size and make, and how much has to come apart to reach the problem. A single worn roller is a small job; a door that’s off-track and bent needs more time. The best way to avoid overpaying is to get a written estimate before work starts and ask what’s included. With us, the estimate is free, and it covers the diagnosis, the parts, and the labor so you’re not guessing at add-ons. The written estimate sets the final price.
Our Service Area Near Manchester
We serve Manchester and the towns around it, including Pinardville, Hooksett, East Merrimack, Goffstown, Suncook, Raymond, Epping, Concord, and Henniker. When your door needs attention, we book the nearest available technician, and same-day service is often possible. For nearby communities, we’re just a short drive out. Whether you’re in Manchester or a surrounding town, we can help with Radiant Garage Door Repair and the full range of door and opener work.
Serving Manchester, NH – Our Local Coverage Area
We serve Manchester and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Garage Door Repair in Manchester
Garage door repair is fixing a door or opener that has stopped working correctly, from replacing a broken spring or cable to realigning a track or sensor. It covers the parts that lift and guide the door, plus the opener that drives it. We diagnose the actual cause before recommending a fix. If you’re unsure what’s wrong, describe the symptom and we’ll get it sorted.
Most repairs take a single visit, often about an hour or less for common jobs like a spring, roller, or sensor fix. A door that’s off-track or has multiple issues can take longer. We’ll give you a realistic time when we schedule, so you’re not left waiting. Call (888) 459-1302 for an exact quote.
Most garage door repairs in Manchester fall between $150 and $600, depending on the part and the job. Spring repair runs $180 – $340 for one spring, and cable repair runs $130 – $250. You’ll always get a written estimate before work starts, and the price is agreed before anyone touches the door. Call (888) 459-1302 for a free estimate.
Yes. We service LiftMaster and Clopay, along with Chamberlain, Genie, Amarr, Wayne Dalton, Craftsman, and Raynor. We cover both openers and doors, so we diagnose your actual equipment rather than working from a generic template. That brand knowledge is why we’re often called for equipment other shops won’t touch. Call (888) 459-1302 to book.
Yes, same-day service is often possible for repair calls in Manchester. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday, closed Saturday. Call (888) 459-1302 and we’ll get a technician to you as soon as we can.
We stand behind our work, and we’ll walk you through what’s covered for your specific repair when we give you the estimate. Terms vary by part and job, so it’s worth asking up front. You’ll know exactly what to expect before work starts. Call (888) 459-1302 with any questions.
Clear the area around the door and the floor of the garage so the technician can work safely and reach the tracks and springs. If you know your door and opener brand, have it ready. Point out anything unusual you’ve noticed, like a noise or a spot where it catches. That helps us diagnose and fix it on the first visit.
Schedule Your Garage Door Repair Service in Manchester Today
A door that’s stuck, noisy, or refusing to close doesn’t fix itself. Call Radiant Garage Door Repair at (888) 459-1302 for a free, no-obligation estimate, and we’ll diagnose the real problem and tell you repair or replace. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Let’s get your door back to working the way it should.
Written by the team at Radiant Garage Door Repair.